Learning the Loop Finish

Posted by  Wednesday, April 10 2013 7:00 am
expert

Whip finishing is a basic fly-tying skill that, once learned, you'll use on each and every pattern you tie. Learning to do it right is essential for creating durable flies that last longer than a few casts.

The loop finish is a way of whip finishing a fly with a loop of line rather than with a whip-finishing tool or your fingers. By wrapping down this loop of line, you create a slip knot around the head of the fly — or anywhere else on the hook you wish to place a knot. Simply tighten the knot to bind the tag end of the thread to the hook shank to secure all your materials into place.

Traditionally, whip finishes have been accomplished in two basic ways: using a whip finishing tool, such as the Thompson or Matarelli, or by hand.

Both the Thompson and Matarelli whip finishing tools work great if you invest some time practicing with them. Whip finishing by hand is popular, too. But since some of us don't have the most nimble hands, fly heads can sometimes turn out sloppy or loose. While the loop finish might not be the solution to all your finishing needs, it may be an easier method to learn initially.

Which method — tool, hand or loop — is better?  While you'll likely find a great deal of debate on the subject, the truth is that it's simply a matter of preference. When applied properly, the loop finish will cinch all your materials tightly in place. A thin layer of head cement will add extra piece of mind, but it's not necessary. And a double loop finish, with four turns of thread, should hold up to all the abuse you can dish out.

Step-by-Step Instructions for the Loop Finish

 

Step 1

Cut a 3-inch section of 6/0 Uni-thread. (We've used orange thread here as it shows up better, but any color will do.)

loop1

Step 2

Place the hook into the vice, and tighten it securely in place.

loop2

Step 3

Attach the tying thread (chartreuse thread) to the hook shank behind the hook eye.

loop3

Step 4

Slide the loop (orange thread) underneath the thread wraps into position onto the top of the hook shank.

loop4

Step 5

Wrap the loop down with four turns of thread from you bobbin.

loop5

Step 6

Give some slack line with the bobbin and attach your hackle pliers to the thread. Cut the tying thread beneath the hackle pliers and bring the thread to the top of the hook shank.

loop6

Step 7

Hold the tag end of the thread with your left hand, and remove the hackle pliers. Place the tips of the hackle pliers through the thread loop (orange thread) and grab the thread once more.

loop7

Step 8

Slip the tag end of thread through the loop while maintaining pressure on the thread with the hackle pliers.

loop8

Step 9

Grab and pull the tag ends of the thread loop (orange thread) with your left hand until the tying thread in snug up against the thread wraps you made earlier.

loop9

Step 10

Give one more quick pull of the tag ends of the loop thread bringing the tying thread under the thread wraps.

loop10

Step 11

Pull up on the tying thread and cut it clean and short near the base of the thread wraps. Place a bit of thin head cement and allow cement to dry.

loop11
Tagged under
Read 681 times
Jason Akl
expert

Jason Akl is a writer, commercial fly tyer and guide with 15 years in the industry. Professionally, he's been a seasonal guide and fly tier that ties commercially and teaches tying classes to both adults and children. Most of his flies make their homes in fly shops in the northern Midwest but some have found their way as far as Europe. As a freelance writer, he's had many written pieces appear in both Canadian and American publications, as well as numerous global websites. When not on the bench or behind the computer, he spends time working with companies such as Daiichi Hooks, Monic Fly Lines or Gatti rods as part of their pro-staff doing product testing pieces and seminars.

You must be signed in to post comments on Bass Pro Shops 1Source. Don't have an account? Please join Bass Pro Shops 1Source.
  • No comments found